International Code Council Fire-Inspector-II 67 - Fire Inspector II Exam Exam Practice Test

High-Pile Combustible Storage Permit Requirements

According to the International Fire Code (IFC) 2021, Section 105.6.23, a permit is required for the storage of high-pile combustible stock when the storage area exceeds 2,500 square feet.

2. Definition of High-Pile Storage

High-pile storage is defined as storage of combustible materials on racks or piles exceeding 12 feet in height (or 6 feet for highly combustible materials, such as rubber and plastics).

IFC Table 3206.2 establishes fire protection requirements based on storage height, area, and commodity class.

3. Verification of Other Options

Option A (225 sq. ft.) – Incorrect, as this is far below the 2,500 sq. ft. permit threshold.

Option B (500 sq. ft.) – Incorrect, as the fire code does not require a permit at this level.

Option C (1,000 sq. ft.) – Incorrect, as the IFC specifies 2,500 sq. ft. as the threshold for requiring a permit.

Reference Sources:

International Fire Code (IFC) 2021 – Section 105.6.23 (High-Pile Combustible Storage Permit Requirements)

IFC Chapter 32 (High-Piled Storage Regulations)

ICC Fire Inspector II Study Guide (2021)

Thus, the correct and verified answer is: D. 2,500. ✅

Platforms used for access to aboveground tanks storing flammable or combustible liquids are regulated by 2021 IFC, Section 5704 – Storage of Flammable and Combustible Liquids.

IFC 5704.2.7.4 – Access to Aboveground Tanks:

"Platforms, ladders, and stairways providing access to aboveground tanks storing flammable or combustible liquids shall be of noncombustible construction."

This ensures that in case of fire, the access structures do not contribute to the spread of flames.

Why Other Options Are Incorrect?

A. At least 4 ft. wide. – The IFC does not specify a required width for platforms.

C. Built of nonferrous, nonsparking metal. – While important in hazardous areas, this is not a general requirement for platforms accessing aboveground tanks.

D. Located no closer than 3 ft. to the side of the tank. – There is no specific 3-ft. clearance requirement in the IFC for platforms.

✅ Correct Answer: B. Built of noncombustible construction.

1.

Exit Sign Letter Height Requirement

According to the International Fire Code (IFC) 2021, Section 1013.5, and the International Building Code (IBC) 2021, Section 1013.5, exit sign letters must be at least 6 inches in height. However, the minimum height requirement for the wording within the sign (e.g., "EXIT") is specifically 4 inches.

The stroke width of these letters must be at least 0.5 inches to ensure visibility.

2. Verification of Other Options

Option A (three inches) – Below the minimum height requirement. Incorrect.

Option C (five inches) – Exceeds the minimum standard but is not the correct minimum required size. Incorrect.

Option D (six inches) – This applies to the total EXIT sign height, but the actual letter requirement is 4 inches. Incorrect.

Reference Sources:

International Fire Code (IFC) 2021 – Section 1013.5

International Building Code (IBC) 2021 – Section 1013.5

NFPA 101: Life Safety Code (Exit Sign Requirements)

When fire inspectors identify code violations, the inspection report must include a description of the violation along with a recommended corrective action. This ensures that the responsible party understands what steps need to be taken to bring the property into compliance.

Reference to Fire Inspector Documentation:

1. 2021 International Fire Code (IFC) – Section 109.3 (Notice of Violation)

IFC 109.3 requires that any notice of violation must include a description of the violation and the necessary corrective action.

The intent is to provide clear guidance on how to remedy the issue to meet fire safety standards.

2. NFPA 1 – Fire Code (2021 Edition) – Section 1.7.6 (Enforcement and Documentation of Violations)

NFPA 1, Section 1.7.6.1 states that violation reports must specify the corrective action required to comply with the fire code.

Detailed Explanation of Answer Choices:

Option A (Incorrect): While a reinspection date may be provided, it is not a mandatory component of an inspection report for code violations.

Option B (Incorrect): A mandatory court date is not always required; enforcement varies depending on jurisdiction and severity of the violation.

Option C (Correct): Recommended corrective action is required in all violation reports as per IFC 109.3 and NFPA 1.7.6.1.

Option D (Incorrect): Potential fines for noncompliance are determined separately and are not necessarily included in the initial violation report.

Thus, the correct and verified answer is: C. Recommended corrective action.

The storage of flammable medical gas supply cylinders inside a building is regulated by 2021 International Fire Code (IFC) Section 5306 – Medical Gas Systems.

IFC Section 5306.2.1 – Storage of More Than 200 Cubic Feet of Medical Gases:

When the quantity of flammable medical gas exceeds 200 cubic feet, it must be stored in a separate room with a minimum 2-hour fire-resistance rating.

The room must also comply with ventilation and explosion control requirements per NFPA 99 (Healthcare Facilities Code).

Why Other Options Are Incorrect?

A. 1/2-hour – Insufficient fire resistance for high-risk gas storage.

B. 1-hour – Does not meet the minimum 2-hour requirement set by the IFC.

D. 3-hour – Exceeds the minimum required by code; the correct requirement is 2-hour fire-resistive construction.

 Reference to Code Modifications and Equivalency Requirements:

According to International Fire Code (IFC 2021), Section 104.10, modifications may be granted if they meet the intent of the code and do not reduce fire and life safety.

The NFPA 1 (Fire Code) and NFPA 101 (Life Safety Code) also allow modifications under specific conditions, provided safety is maintained.

 Understanding the Exception in the Question:

The question asks for conditions that DO NOT warrant a modification.

Using an alternative building material alone does not justify a modification unless it meets equivalent safety standards.

Code modifications are granted based on maintaining or improving safety, not simply changing materials.

 Clarification of Incorrect Answer Choices:

A. Modification does not lessen health, life, and fire safety → Correct condition for modification, so incorrect answer

IFC 104.10 allows modifications as long as safety is not compromised.

C. Modification is in compliance with the intent and purpose of the code → Correct condition for modification, so incorrect answer

Codes provide flexibility if the intent of fire and life safety is still met.

D. Special individual reason makes the strict letter of the code impractical → Correct condition for modification, so incorrect answer

Some codes allow modifications if strict compliance is impractical, provided alternative safety measures are implemented.

 Conclusion:

The correct and verified answer is B (modification requires the use of an alternative building material) because material substitution alone does not justify a modification unless safety is maintained, as per IFC 104.10 and NFPA standards.

Refrigeration systems and units are regulated under IFC 2021, Section 605 – Refrigeration Equipment, and the requirement for emergency signs, charts, and labels is tied to the NFPA 704 Hazardous Materials Identification System.

IFC 2021, Section 605.12.3 – Signage for Refrigeration Systems:

States that approved emergency signs, charts, and labels must be provided when the refrigerant quantity exceeds 220 pounds for Group A1 refrigerants.

Definition of Group A1 Refrigerants (Low Toxicity, Low Flammability):

Examples include R-134a, R-410A, and R-22, which are commonly used in commercial and industrial HVAC systems.

Why Other Options Are Incorrect?

A. 30 lb. – Too low; labeling requirements do not apply at this threshold.

B. 100 lb. – Incorrect; the IFC requirement specifies 220 lb.

C. 200 lb. – Close, but still below the 220 lb. threshold.

 Reference to Explosive Storage Regulations:

The International Fire Code (IFC 2021), Section 5604 and NFPA 495 (Explosive Materials Code) regulate the storage distances for Class 1.3 explosives (which include low explosives such as propellants and display fireworks).

Table 5604.5.2(3) of the IFC provides minimum separation distances between explosives storage and public traffic routes based on the weight of the explosives.

 Determining the Correct Distance:

According to IFC Table 5604.5.2(3), for 1,750 lb. of Class 1.3 explosives, the minimum separation distance from a public traffic route is 115 feet.

 Clarification of Incorrect Answer Choices:

A. 50 ft. → Incorrect

50 feet is too close and does not meet the safety requirements for explosive storage.

B. 75 ft. → Incorrect

75 feet is insufficient based on IFC and NFPA separation tables.

D. 150 ft. → Incorrect

While more distance is safer, the minimum requirement is 115 feet, making 150 feet unnecessary per code.

 Conclusion:

The correct and verified answer is C (115 feet) based on IFC Table 5604.5.2(3) and NFPA 495 requirements for Class 1.3 explosives storage near public traffic routes.

According to the International Fire Code (IFC) 2021, when specific fire safety requirements are not explicitly provided for in the code, the responsibility to determine the applicable requirements falls upon the Fire Code Official.

Reference from the IFC (2021):

IFC Section 104.1 – General Authority and Responsibilities:

This section explicitly grants the Fire Code Official the authority to interpret the code and determine the necessary safety measures in cases where the code does not provide specific guidance.

It states: "The fire code official is hereby authorized to enforce the provisions of this code and shall have the authority to render interpretations of the code and to adopt policies and procedures in order to clarify the application of its provisions."

IFC Section 104.9 – Alternative Materials and Methods:

This section further supports the authority of the Fire Code Official by allowing them to approve alternative fire safety measures when strict compliance with the code is not feasible.

Why Other Options Are Incorrect?

A. City Manager:

The city manager is responsible for administrative and operational management but does not have the authority to interpret or enforce fire code requirements.

B. Legal Counsel:

Legal counsel provides legal advice but does not have jurisdiction over fire safety code enforcement.

C. Board of Appeals:

The board of appeals reviews disputes and interpretations made by the Fire Code Official, but they do not have primary responsibility for determining applicable fire safety requirements.

Final Conclusion:

The Fire Code Official is the designated authority responsible for interpreting and applying fire safety requirements in situations where the International Fire Code (IFC) does not explicitly provide specific provisions.

 Reference to ICC Fire Code Regulations:

According to the International Fire Code (IFC) Section 308.1.5 (2021 Edition), the use of open-flame devices, including candles, is prohibited in dormitories, sleeping rooms, and similar occupancies unless specifically approved by the fire code official.

The regulation exists to prevent fire hazards in areas with high occupant density and potentially limited egress routes.

 Fire Safety Concerns in Dormitories:

Dormitories typically contain highly combustible materials such as bedding, curtains, and furniture, making them susceptible to rapid fire spread.

The presence of multiple residents in a shared living space increases the risk of fire-related casualties.

Even in sprinklered buildings, candles pose an unnecessary ignition risk that could endanger occupants before the activation of fire suppression systems.

 Clarification of Incorrect Answer Choices:

B. may be used in a sprinklered dormitory → Incorrect

While fire sprinklers help control fires, they do not prevent ignition, and the prohibition still applies regardless of sprinkler systems.

C. must be kept a minimum of 12 inches from combustibles → Incorrect

This rule applies to general open-flame devices in some circumstances but does not override the outright ban on candles in dormitories.

D. must be kept a minimum of 36 inches from combustibles → Incorrect

Similar to option C, maintaining a distance from combustibles does not exempt candles from being prohibited in dormitory settings.

 Conclusion:

The correct and verified answer is A (Candles may not be used) based on the International Fire Code (IFC) Section 308.1.5, ensuring fire safety compliance in dormitory settings.

The occupant load for an R-2 building's common patio area must be calculated using an occupant load factor. The correct factor is 15 gross sq. ft. per person.

Reference to Fire Inspector Documentation:

1. 2021 International Building Code (IBC) – Table 1004.5 (Occupant Load Factor)

For outdoor areas (such as patios and terraces), the applicable factor is 15 gross sq. ft. per person.

2. 2021 International Fire Code (IFC) – Section 1004.5 (Outdoor Occupant Loads)

The 15 gross per person requirement is applied to common outdoor gathering areas in residential occupancies (R-2).

Detailed Explanation of Answer Choices:

Option A (Incorrect): 50 net per person applies to storage areas, not patios.

Option B (Incorrect): 11 gross per person is used for business occupancies (B), not residential patios.

Option C (Correct): 15 gross per person is the correct calculation factor for common outdoor spaces in R-2 buildings.

Option D (Incorrect): The code official does not assign occupant load values arbitrarily—they follow IBC Table 1004.5.

Thus, the correct and verified answer is: C. 15 gross per person.

Understanding Type III Construction

According to the International Building Code (IBC) 2021, Section 602.3, Type III construction is a mix of noncombustible and combustible materials.

Exterior walls must be noncombustible or fire-retardant-treated wood, while interior structural elements (such as floors, roofs, and partitions) can be wood.

2. Common Uses of Type III Construction

Churches, schools, apartment buildings, and mercantile (retail) structures are often built using Type III construction because it balances fire resistance with cost-effectiveness.

Many low-rise residential and commercial buildings use this type due to its ability to support multiple stories while maintaining some fire protection.

3. Verification of Other Options

Option A (Type I) – Incorrect, as Type I construction is entirely noncombustible (steel/concrete) and used for high-rises, not typical for churches, schools, or apartments.

Option B (Type II) – Incorrect, as Type II construction is fully noncombustible but has lower fire resistance than Type I, mainly used for commercial buildings, warehouses, and low-rise offices.

Option D (Type IV) – Incorrect, as Type IV (heavy timber) is rarely used for schools and apartments, though some older churches may use it.

Reference Sources:

International Building Code (IBC) 2021 – Section 602.3 (Type III Construction Definition)

NFPA 220: Standard on Types of Building Construction

ICC Fire Inspector II Study Guide (2021)

Thus, the correct and verified answer is: C. Type III. ✅

 Reference to Magnesium Dust Collection Requirements:

NFPA 484 (Standard for Combustible Metals), Section 9.3.2, requires that magnesium dust from grinding, buffing, or wire brushing must be collected using a liquid precipitation-type separator.

The International Fire Code (IFC 2021), Section 2205, also references proper dust collection for combustible metals like magnesium.

 Why Use a Liquid Precipitation-Type Separator?

Magnesium dust is highly combustible and reacts violently with air and moisture.

A liquid precipitation-type separator prevents dust accumulation and ignition by using a liquid medium to safely capture and neutralize metal dust particles.

Other collection methods can generate static electricity or allow dangerous dust accumulation, increasing fire and explosion risks.

 Clarification of Incorrect Answer Choices:

A. Cloth screen arrestor → Incorrect

Not effective for combustible metal dust, as magnesium dust can ignite easily and pass through fabric filters.

B. Low-pressure cyclone → Incorrect

Cyclones are used for larger particulate matter, but not suitable for fine magnesium dust due to fire and explosion hazards.

C. Dry-type dynamic precipitator → Incorrect

Dry-type systems can accumulate magnesium dust, creating an explosion hazard.

 Conclusion:

The correct and verified answer is D (liquid precipitation type of separator) based on NFPA 484 Section 9.3.2 and IFC 2205, ensuring safe collection of magnesium dust during grinding, buffing, or wire brushing operations.

The interior finish requirements for walls and ceilings in an atrium are regulated under the 2021 International Building Code (IBC), Section 404 – Atriums, and Table 803.11 – Interior Wall and Ceiling Finish Requirements.

IBC Section 404.8 – Interior Finish in Atriums:

"The interior finish of walls and ceilings in an atrium shall be not less than Class A."

Class A interior finishes have the highest level of fire resistance and low flame spread to minimize fire hazards in large open spaces like atriums.

Class A Interior Finish Ratings (Per ASTM E84 and NFPA 286):

Flame Spread Index: 0 – 25

Smoke Developed Index: 0 – 450

Why Other Options Are Incorrect?

B. Class B – Less fire-resistant than Class A, not permitted for atriums.

C. Class C – Provides even lower fire protection, making it unsuitable.

D. Class D – Not recognized as an acceptable interior finish classification for atriums.

To determine the occupant load of a 50,000 gross square foot airport terminal concourse, we use the occupant load factor from 2021 IBC Table 1004.5.

Step 1: Identify the Occupant Load Factor for an Airport Concourse

According to IBC Table 1004.5, the occupant load factor for an airport terminal concourse is 20 sq. ft. per person (gross).

Step 2: Calculate the Occupant Load

50,00020=2,500 occupants\frac{50,000}{20} = 2,500 \text{ occupants}2050,000​=2,500 occupants

Reference to Fire Inspector Documentation:

1. 2021 International Building Code (IBC) – Table 1004.5 (Occupant Load Factor for Airport Concourses)

20 sq. ft. per person is assigned for airport concourses.

2. 2021 International Fire Code (IFC) – Section 1004.1.2 (Occupant Load Determination)

Gross area calculations must follow the correct occupant load factor per IBC Table 1004.5.

Detailed Explanation of Answer Choices:

Option A (Incorrect): 200 is too low based on proper calculations.

Option B (Incorrect): 500 is also too low.

Option C (Incorrect): 1,000 is below the required calculation.

Option D (Correct): 2,500 is the correct calculation based on IBC Table 1004.5.

Thus, the correct and verified answer is: D. 2,500.

IFC Section 901.5 (Acceptance Tests) requires fire protection systems, including fire alarms, to be tested upon completion to ensure compliance with NFPA 72 (National Fire Alarm and Signaling Code) and the IFC. The contractor’s verification of full compliance (B) signals readiness for the official acceptance test by the fire code official, ensuring all components are installed and functional. Option A (zone-by-zone testing) is impractical for final acceptance. Option C ties the test to water supply, irrelevant to alarms. Option D (one year) is excessive and not required by IFC or NFPA 72 for initial acceptance. Thus, B is correct.

IFC Section 903.3.5 and Appendix B (Fire-Flow Requirements) allow a reduction in fire flow when sprinklers are installed. For a Type II-B building (noncombustible, unprotected), the base fire flow (7,000 gpm) reflects a large, unsprinklered structure (e.g., per Table B105.1(2)). With full sprinkler protection, IFC B105.2 permits a reduction to as low as 25% of the original flow or the sprinkler demand (whichever is greater), typically 1,500 gpm for commercial buildings per NFPA 13 standards, assuming adequate water supply. Options B, C, and D exceed this minimum without justification. Thus, A is correct.

The maximum travel distance allowed in a one-story Group F-2 (Factory Industrial - Low Hazard) occupancy with automatic sprinklers and automatic smoke and heat vents is regulated by 2021 International Fire Code (IFC) Table 1017.2 – Exit Access Travel Distance.

IFC Table 1017.2 – Maximum Travel Distance:

For a Group F-2 occupancy equipped with an automatic sprinkler system, the maximum allowable exit access travel distance is 400 feet.

However, when automatic smoke and heat vents are installed, the travel distance is limited to 350 feet.

This is because while the sprinklers control fire spread, smoke and heat vents help with smoke control, allowing for extended egress distances but not as much as without them.

Why Other Options Are Incorrect?

A. 250 ft. – Too restrictive; the IFC allows a longer travel distance in this scenario.

B. 300 ft. – Less than the allowed 350 ft.

D. 400 ft. – Only applicable without smoke and heat vents.

A fire code official has authority to enter buildings for fire safety inspections, but they must comply with legal entry requirements. The Fourth Amendment of the U.S. Constitution and fire codes restrict entry without permission, an administrative warrant, or legal authority.

Fire code officials do NOT have the right to enter vacant buildings at any time without proper authorization.

Reference to Fire Inspector Documentation:

1. 2021 International Fire Code (IFC) – Section 104.3 (Right of Entry)

IFC 104.3 states that a fire code official may only enter a building at reasonable times to conduct inspections, with consent or a legal warrant.

If entry is refused, the fire code official must obtain an administrative warrant before proceeding.

2. Fourth Amendment of the U.S. Constitution

Protects property owners from unlawful searches and seizures without proper legal authority.

Detailed Explanation of Answer Choices:

Option A (Correct): Fire code officials cannot enter vacant buildings at any time without permission or a warrant.

Option B (Incorrect): Fire code officials can enter a factory floor with permission from the owner/occupant.

Option C (Incorrect): Fire code officials can inspect public areas of malls during business hours since these spaces are open to the public.

Option D (Incorrect): Fire code officials can enter a warehouse’s interior with an administrative warrant, which is legally authorized for inspections.

Thus, the correct and verified answer is: A. Vacant buildings at any time.

Fire-Resistance Rating for Nonbearing Walls in Type IV Construction

Type IV (Heavy Timber) construction, as defined by the International Building Code (IBC) 2021, Section 602.4, consists of large, solid or laminated wood members.

Interior nonbearing walls and partitions in Type IV construction are not required to have a fire-resistance rating (0 hours) unless they separate different occupancies or are specifically mandated by another code provision.

2. Why Type IV Does Not Require a Rating for Nonbearing Walls

The heavy timber components inherently provide fire resistance due to their large cross-section, which chars on the surface and slows fire penetration.

IBC Table 601 confirms that interior nonbearing walls in Type IV construction do not have a required fire-resistance rating.

3. Verification of Other Options

Option B (1 hour) – Incorrect, as Type IV does not require a 1-hour rating for interior nonbearing walls unless specific conditions apply.

Option C (1-1/2 hours) – Incorrect, as there is no code requirement for this level of rating in Type IV nonbearing walls.

Option D (2 hours) – Incorrect, as Type IV walls are not rated unless separating occupancies.

Reference Sources:

International Building Code (IBC) 2021 – Section 602.4 (Type IV Construction Requirements)

IBC Table 601 (Fire-Resistance Ratings for Building Elements)

ICC Fire Inspector II Study Guide (2021)

Paint Spray Booth Clearance Requirements

According to the International Fire Code (IFC) 2021, Section 2404.3.2, paint spray booths must have a minimum clearance of 18 inches from unprotected combustible materials.

This clearance requirement helps prevent heat transfer, fire spread, and ignition of nearby combustible materials due to the operation of the spray booth.

2. Why 18 Inches is the Correct Answer

Spray booths generate overspray, vapors, and heat, making clearance essential for fire prevention.

The requirement applies to combustible walls, ceilings, and storage materials surrounding the spray booth.

If combustibles are within 18 inches, additional fire protection such as fire-rated barriers or sprinkler protection may be required.

3. Verification of Other Options

Option A (12 inches) – Incorrect, as the IFC mandates a minimum 18-inch clearance.

Option C (24 inches) – Exceeds the standard clearance requirement but is not the official minimum. Incorrect.

Option D (36 inches) – Some jurisdictions may require larger clearances, but IFC mandates 18 inches as the minimum. Incorrect.

Reference Sources:

International Fire Code (IFC) 2021 – Section 2404.3.2 (Paint Spray Booth Clearance Requirements)

NFPA 33: Standard for Spray Application Using Flammable or Combustible Materials (Clearance Guidelines)

ICC Fire Inspector II Study Guide (2021)

Thus, the correct and verified answer is: B. 18 inche

A container in a clean-agent extinguishing system must be refilled or replaced if it experiences a loss of more than 5% of its original weight or a loss in original pressure of more than 3%. This requirement ensures the system maintains sufficient agent concentration for fire suppression.

Reference to Fire Inspector Documentation:

1. NFPA 2001 – Standard on Clean Agent Fire Extinguishing Systems (2022 Edition)

NFPA 2001, Section 7.3.2.1 states that a container must be refilled or replaced if the weight loss exceeds 5% or the pressure loss exceeds 3% from the original fill pressure.

These limits are set to maintain system effectiveness and ensure that a clean-agent system can properly discharge in case of a fire.

2. 2021 International Fire Code (IFC) – Chapter 9 (Fire Protection Systems)

IFC 904.10 requires that clean-agent systems be maintained per NFPA 2001 to ensure reliability.

Detailed Explanation of Answer Choices:

Option A (Correct): 3% pressure loss is the correct threshold beyond which a container must be replaced or refilled.

Option B (Incorrect): While 5% is correct for weight loss, it is not the correct value for pressure loss.

Option C (Incorrect): A 10% pressure loss is too high and would compromise system performance before reaching the replacement threshold.

Option D (Incorrect): 12% is well beyond the acceptable loss limit and would pose a significant safety risk.

Thus, the correct and verified answer is: A. 3

Foamed plastics or materials containing foamed plastics used for stage scenery must meet strict fire performance requirements to prevent rapid flame spread and fire hazards in assembly occupancies.

The correct fire test standard for these materials is UL 1975 – Standard for Fire Tests for Foamed Plastics Used for Decorative Purposes.

Reference to Fire Inspector Documentation:

1. 2021 International Fire Code (IFC) – Section 807.4.2 (Foamed Plastics for Stage Scenery)

IFC 807.4.2 states that foamed plastics used in scenery must be tested and approved per UL 1975 to ensure fire safety.

2. UL 1975 – Standard for Fire Tests for Foamed Plastics Used for Decorative Purposes

This standard evaluates the flammability and smoke production of foamed plastics used in decorative applications, including stage scenery.

Detailed Explanation of Answer Choices:

Option A (Correct): UL 1975 is the required test standard for foamed plastics used in stage scenery, ensuring compliance with IFC 807.4.2.

Option B (Incorrect): NFPA 11A deals with foam-water fire suppression systems, not foamed plastics for decorative use.

Option C (Incorrect): CPSC 16CFR relates to consumer product safety regulations but does not address fire safety for foamed plastics on stage scenery.

Option D (Incorrect): ASTM D 1784 is a test for rigid PVC plastics and does not apply to foamed plastics used for stage scenery.

Thus, the correct and verified answer is: A. UL 1975.

Efficient scheduling minimizes travel time and maximizes inspection coverage, a practical aspect of fire inspection management (not explicitly detailed in the IFC but implied in Section 106.2, Inspections). Selecting occupancies in the same geographic area (C) reduces travel, allowing more time for thorough inspections. Option A undermines the comprehensive nature of inspections required by IFC Section 106.1. Option B could compromise inspection quality, not efficiency. Option D focuses on violation history, which doesn’t inherently improve scheduling efficiency and may skew priorities. Thus, C is the most logical and IFC-aligned choice.

Exit Announcements in Motion Picture Theaters

According to the International Fire Code (IFC) 2021, Section 403.9.1.2, motion picture theaters must provide an audible announcement informing occupants of exit locations no more than 5 minutes prior to the start of each program.

This requirement ensures that audience members are aware of exit locations in case of an emergency, enhancing fire safety in crowded venues.

2. Verification of Other Options

Option B (10 minutes) – Exceeds the IFC maximum timeframe. Incorrect.

Option C (20 minutes) – Not specified in the IFC as a valid timeframe. Incorrect.

Option D (30 minutes) – Far beyond the required timeframe and would likely be ineffective. Incorrect.

Reference Sources:

International Fire Code (IFC) 2021 – Section 403.9.1.2 (Theater Exit Announcements)

NFPA 101: Life Safety Code (Theater Occupancy Requirements)

ICC Fire Inspector II Study Guide (2021)

 Reference to Fire Extinguisher Requirements in Buildings Under Construction:

NFPA 241 (Standard for Safeguarding Construction, Alteration, and Demolition Operations) Section 13.6.1 and IFC 3309.1 require that:

A minimum of one fire extinguisher per floor is required.

Additional extinguishers are required based on stairwells and floor area.

If a building under construction has two stairways, a minimum of two fire extinguishers must be provided per floor to ensure adequate fire protection coverage.

 Fire Safety Considerations for Construction Sites:

Construction sites pose a high fire risk due to temporary electrical systems, combustible materials, and lack of finished fire suppression systems.

Fire extinguishers must be readily available and evenly distributed near exit stairways and pathways for rapid access in case of an emergency.

 Clarification of Incorrect Answer Choices:

A. 1 → Incorrect

One extinguisher is the minimum required for floors with only one exit/stairway, but a building with two stairways requires at least two extinguishers.

C. 3 → Incorrect

While more extinguishers can be added for larger areas or high-risk work zones, the minimum requirement remains two for two stairwells.

D. 4 → Incorrect

There is no general requirement for four extinguishers per floor unless dictated by floor size and hazard level.

 Conclusion:

The correct and verified answer is B (2 fire extinguishers per floor) based on NFPA 241 and IFC 3309.1, ensuring compliance with fire safety standards for buildings under construction.