Huawei H12-261 today updated questions - Verified by Huawei Experts

HCIE-Routing & Switching (Written) Questions and Answers

Question 1

Which of the following address prefixes indicates that the address is a globally unique and globally routable IPv6 unicast address, similar to a public IPv4 address?

Options:

::1/128

FE80::/10

FC00::/7

2000::/3

Question 2

Which of the following statements regarding route-policies are true?

Options:

If more than one node is defined in a route-policy, the matching mode of at least one node must be permit

An advanced ACL can be used in a route-policy to filter routes

A route-policy can filter only default routes

If the entry permit :: 0 less-equal 128 is defined, all IPv6 routes are permitted

Question 3

Routers HW1 and HW2 are IP Multicast routers. These routers use (S, G) entries for multicast packet forwarding. Which of the following address types are used in the “S” entry?

Options:

The block of administratively scoped multicast addresses

Source Specific multicast addresses

SDP/SAP addresses

Any class A, Class B, or Class C host address

GLOP addresses

Question 4

HW has a Frame Relay network with two sites (a headquarters site and a remote site) connected by a single PVC. RIP version 2 is running in the network. A new remote site is added and HW has ordered a second PVC between this site and the headquarters site. All Frame Relay interface IP addresses are in a single subnet. The customer configured Frame Relay DLCI mappings and can successfully ping from the new remote to the headquarters site as well as to the other remote site. However, the new router does not have a route in its route table to the other remote site’s LAN, and cannot ping the LAN interface or any hosts on that LAN. What is most likely causing the problem?

Options:

Triggered updates should be configured on the headquarters router, to directly forward routing updates between the two remote sites

The headquarters site router has split-horizon enabled on the frame-relay interface

Neighbor statements are not configured on the two remote sites, pointing to all other sites

The frame-relay IP to DLCI mappings are incorrectly configured

RIP cannot propagate routing updates over a partial mesh frame-relay configuration, so another routing protocol should be selected

Question 5

Which of the following statements regarding control are true?

Options:

For node 10, the relationship between if-match community-filter 1 and if-match as-path-filter 1 is “AND.”

Default OSPF, IS-IS, and BGP routes can be advertised.

An AS-Path-filter filters routes based on the AS-Path attribute to affect route selection

The import-route BGP command can be used to import IBGP routes

Question 6

In a BGP EVPN distributed gateway scenario, which of the following packet types is required to implement VM migration?

Options:

Type 1

Type 2

Type 3

Type 5

Type 4

Question 7

Most popular Layer 2 tunneling technologies include VXLAN, TRILL, NVGRE, and MPLS.

Options:

True

False

Question 8

Which IPv6 header field has a function similar to that of the “Type of Service” field in an IPv4 header?

Options:

Flow Label

Traffic Class

Next Header

Version

Question 9

A network with the typology shown in the figure below is set up in a lab. On the network, SW1 uses the default configurations, and STP disables on SW2. Given this information, which of the following statements is true?

Options:

Go/0/2 of SW2 enters the Discarding state.

G0/0/1 of SW1 enters the Discarding state.

G0/0/1 of SW2 enters the Discarding state.

No interface is blocked.

G0/0/2 of SW1 enters the Discarding state.

Question 10

Which of the following configurations can be used to prevent users from connecting a hub to an access port on a switch allowing multiple device to access the network?

Options:

Option A

Option B

Option C

Option D

Question 11

To improve delay and jitter on frame relay links, we can fragment and assemble the frame between multiple PVCs. This is similar to what happens with PPP multilink.

Options:

FALSE

TRUE

Question 12

When receives or transmits data frames on an access port, what will the switch do?

Options:

Switch will send tagged frames belong to a specified vlan

When received a tagged frame from an access port. Switch may forward it vlan

Switch will learn the MAC-address only on access port

Switch only receives untagged frames from access port and drop all tagged frames

Question 13

Huawei switches SWA and SWB are connected through seven physical Ethernet links and are configured with static link aggregation. On SWA, the interface and are configured in the following sequence: Ethernet 1/0/1, Ethernet 1/0/2, Ethernet 1/0/3, Ethernet 1/0/4, Ethernet 1/0/5, Ethernet 1/0/6,

Ethernet 1/0/7. If only six ports are supported in a LAG on SWA and SWB, which of the following statements is true?

Options:

If the configurations of different ports are consistent, SWA selects one of the seven ports at random to be the Unselected port of the LAG.

If the configurations of different ports are consistent, Ethernet 1/0/6 is the Unselected port of the LAG.

If the configurations of different ports are consistent, Ethernet 1/0/7 is the Unselected port of the LAG.

If the configurations of different ports are consistent, Ethernet 1/0/1 is the Unselected port of the LAG.

Question 14

A new Syslog server is being installed in the HW network to accept network management information. What characteristics apply to these Syslog messages?

Options:

Its transmission is acknowledgment

Its transmission is secure

Its transmission is not secure

Its transmission is not reliable

Its transmission is not acknowledged

Its transmission is reliable

Question 15

Both IS-IS and OSPF run on a network as shown in the following figure. Route import is configured on RTB and RTC respectively. All the routers are connected through GE interfaces. Routes to the network segment 2.2.2.2/32 is imported to the OSPF process using the import-route direct command on RTD. The default settings are retained for all the other configurations. Which of the following statements regarding this network is false?

Options:

The following configuration can be performed on RTC to filter out only routes to the network segment 2.2.2.2/32 when RTC imports routes:[RTC] ip ip-prefix 10 index 1 deny 2.0.0.0 8 less-equal 32[RTC-isis-1]filter-policy ip-prefix 10 import

On RTB, adjust the IS-IS preference to 160 to avoid generation of sub-optimal routes on the network

The following configuration can be performed on RTC to filter out routes from RTD to the network segment 2.2.2.2/32 when RTC imports OSPF routes:[RTC-acl-basic-2001]rule 5 deny source 2.0.0.0 0.255.255.255[RTC-acl-basic-2001]rule 10 permit[RTC-isis-1]filter-policy 2001 import

RTB learns that RTA is the next hop of the route to the network segment 2.2.2.2/32

Question 16

Based on the preceding networking and configurations, which of the following statements is true?

Options:

Route flapping occurs

RTB and RTC cannot establish a neighbor relationship

RTA and RTB cannot establish a neighbor relationship

A neighbor relationship can be established; all network segments are reachable

Question 17

Which of the following technologies use tunnels to allow for communication between devices with IPv6 addresses?

Options:

ISATAP

6to4

NAT64

Dual Stack

Question 18

Which of the following statements regarding OSPFv3 LSAs are true?

Options:

The Link State ID of an Inter-Area-Prefix-LSA contains prefix information

Router-LSAs and Network-LSAs do not contain routing information

Inter-Area-Prefix-LSAs contain link-local information

When the Referenced Link State Type of an Intra-Area-Prefix-LSA is 2, the Referenced Link State ID contains the interface ID of the DR

Question 19

Which of the following statements regarding optimal route selection of various protocols is true?

Options:

All routes learned through OSPF in the LSDB are added to the IP routing table

The optimal route is selected after comparison costs of routes that are learned through BGP and destined for the same network segment

The optimal route is selected after comparison between preferences of routes that are learned through BGP and OSPF and that are destined for the same network segment

BGP routes with unreachable next hops are also added to the IP routing table

Question 20

By default, WRED is configured on a newly deployed Huawei router. Which of following statements regarding WRED are true?

Options:

When traffic exceeds the minimum threshold, WRED starts to discard all inbound traffic (tail drop).

Traffic with low bandwidth is more likely to be discarded than traffic with high bandwidth.

WRED selectively discards multiple TCP flows to avoid global synchronization.

WRED can be used to set different drop thresholds and packet loss ratio for data packets with different priorities.

Question 21

The figure shows router data. Which of the following statements is false?

Options:

The system ID of R3 is 0003.0000.000

3R is a Level-1-2 router.

R3 is the DlS of a Level-1 link.

R3 Is the DI5 of a level 2 link.

Question 22

Which of the following statements regarding the process of sending and receiving data frames on a port in access link-type is true?

Options:

Tagged data frames that are received are directly discarded.

Only untagged data frames are received.

VLAN tags are removed before data frames are sent.

A switch learns the destination MAC address in the data frames when they are received on the switch's port.

Question 23

Router HW1 and Router HW2 are connected to network A and B Network B respectively. Referring to the figure, if you want to set up an IPsec VPN tunnel between HW1 and HW2, which of the following ACL rules needs to be configured on HW1 to transmit the traffic across network A and B pass through the encrypted VPN tunnel?

Options:

rule permit ip source 10.1.2.0 0.0.0.255 destination 10.1.1.0 0.0.0.255

rule permit ip source 10.1.1.0 0.0.0.255 destination 10.1.2.0 0.0.0.255

rule permit ip source 10.1.1.0 0.0.0.255 destination 192.168.1.2 0

rule permit ip source 192.168.1.1 0 destination 10.1.2.0 0.0.0.255

rule permit ip source 192.168.1.1 0 destination 192.168.1.2 0

Question 24

Which of the following statements regarding RADIUS are true?

Options:

Authentication, authorization, and accounting are separated in RADIUS protocol.

RADIUS authentication and Portal authentication cannot be used together because users can be authenticated using the Portal server when Portal authentication is enabled.

MAC address authentication does not require a user name and password. Therefore, users cannot be authenticated through RADIUS when using MAC address authentication.

RADIUS supports user access in wired and wireless modes.

Question 25

As shown in the configuration management, R1 OSPF R1, () staff configured but can not learn the routing of other routers, then the possible reason is.

[R1]ospf

[Rl-ospf-1]area 2

[R1-ospf-1-area-0.0.0.2]network 10.0.13.1 0.0.0.0

Options:

The area configured by this router is different from the area ID ID of its home router.

This router is not configured with the number OSPF

The router's announcement network address does not match the interface mask.

This router is not configured with functional authentication, but the router is configured with function neighbor authentication.

Question 26

A VXLAN tunnel can be established between two VTEPs and shared by all VXLAN network Identifiers (VNIs) between two NVE nodes.

Options:

TRUE

FASE

Question 27

How long will a Huawei switch running RSTP wait before aging out the BPDUs on an interface?

Options:

Hello time interval

6 seconds

MaxAge interval

BPDUs on the interface will not be aged out.

Forward delay

Question 28

If host HW1 on the network wants to join a video conference, what will the host do?

Options:

The host multicasts an 1GMPv2 Membership Report message that carries the expected multicast address to the local network.

The host multicasts an IGMPv2 Membership Report message with the multicast address for all PIM routers (224.0.0.2) to the local network.

The host unicasts an IGMPv2 Membership Report message to the default router on the local network.

The host unicasts an IGMPv2 Membership Report message to the RP.

Question 29

Which of the following statements correctly describes the corresponding MPLS TTL processing mode?

Options:

On an MPLS VPN, if the structure of the MPLS backbone network needs to be shielded, the Uniform mode is recommended for VPN packets,

In Uniform mode, when IP packets enter an MPLS network, the ingress node decrements the IP TTL by one and the MPLS TTL field has a fixed value.

The TTL field in an MPLS label serves the same function as that in an IP packet header. That is, the TTL is used to prevent loops on an MPLS network.

In Pipe mode, when IP packets enter an MPLS network, the ingress node decrements the IP TTL by one and copies this new value to the MPLS TTL field.

Question 30

Which of the following statements regarding PPPoE data frames are true?

Options:

The Session JD field of a PPP session must be the value specified in the Discovery phase and cannot be changed.

After a PPPoE session is set up, all Ethernet packets are unicast.

The Ethemet_Type field has a fixed value of 0x8863.

When PPPoE is used to transmit session data, Code must be set to 0x0.

Question 31

In which of the following scenarios will gratuitous ARP packets be sent?

Options:

A host connected to the switch sends a ping packet.

The DHCP client receives an acknowledgment message from the server

A new host with an IP address is connected to the network.

The master and backup devices are elected in VRRP.

Question 32

A DR needs to be elected from a set of candidate PIM-SM routers for multicast data forwarding on the source Which of the following statements regarding DR election rules is true?

Options:

The PIM-SM router with the lowest DR priority is elected as the DR.

The PIM-SM router with the smallest IP address is elected as the DR.

The PIM-SM router with the longest interface mask is elected as the DR.

DR priorities of the PIM-SM routers are compared first. If their DR priorities are the same, their interface IP addresses are then compared.

Question 33

The network management has set a traffic management strategy as follows:

The router port that should be used by the policy has been idle for about 10 c1 seconds. Sometimes the type of massive burst is in the instant, so the coloring is green.

How many bytes will the packet have?

Options:

6K bytes

32K bytes

48128 bytes

80128 bytes

Question 34

Which messages are sent to the agent by the network management station (NMS) SNMPv1?

Options:

Trap, Get, and Set messages

Only Trap messages

Get, Set, and GetNext messages

Get, Set, and GetBulk messages

Get, Set, GetNext, and GetBulk messages

Question 35

Multicast IP 229.130.130.1, MAC: The address is the corresponding address of

Options:

00-00-5E-02-82-01

00-00-5E-82-82-01

01-00-5E-82-82-01

01-00-5E-02-82-01

Question 36

A network administrator is planning to use an automatic 6to4 tunnel to transmit IPv6 data on an IPv4 network. If the IPv4 address of the router interface is 138.14.85.210, the corresponding tunnel address should be 2001:8a0e:55d2:l:230:65ff:fe2c:9a6.

Options:

TRUE

FALSE

Question 37

Which of the following statements regarding CE dual-homing features is false?

Options:

The VRFs of two PEs connected to the same CE can belong to different VPNs.

In the CE dual-homing networking, loops may occur. You can usq route-tag to resolve this issue.

A CE dual-homing network where a CE is connected to two PEs ensure high network reliability.

A CE connects to the backbone network through two links that work in load balancing or primary/secondary mode.

Question 38

Which of the following statements regarding ISIS route summarization is true?

Options:

Route summarization can be configured and takes effect on all types of routers.

Route summarization takes effect only on Level-1 routers

Route summarization takes effect only on Level-2 routers.

Route summarization takes effect only on Level-1-2 routers.

Question 39

If there are multiple receiver groups in a broadcast, IGMP-Snooping, manages the switcher on the receiver's switch. When the receiver changes from the switch

After receiving the general post-query query group query report, how many recipients should return

Options:

All recipients will respond to the Report message.

Only if it is running, all receivers will return to the IGMPv1 Report response message.

When the first recipient of the louder response time is sent, the report is sent, and the other recipients are not sent.

Only if it is running, all receivers will return to the IGMPV2 Report response message.

Question 40

If the interface of the router is out of A GigabitEthernet0/0/0 OSPFv3 Hello Option 0x000013, the field value is the following.

The correct one is more ( )

Options:

The interface of the router belongs to the area A GigabitEthernet0/0/0 NSSA

The router will participate in the routing calculation. A GigabitEthernet0/0/0 IPv6 meter

Router is capable A OSPFv3 standby forwarding device

Router Support Flooding

Question 41

In the ( ) data encapsulation, the first VLAN of the first field is 802.1Q 6bit.

Options:

True

False

Question 42

If the PIM-SM is running in the broadcast network, the forwarding tree needs to be set up between the broadcast source and the receiver to enable the receiver to receive the broadcast data set.

Then for the group forwarding tree option, the following is the correct description of the built broadcast? Multiple ( )

Options:

The RP RPT is constructed with the recipient.

The multicast source and the RP RPT are constructed by the tree.

RP SPT and the recipient's construction is the tree

The multicast source and the RP SPT are constructed by the tree.

Question 43

OSPFv3 OSPFv2 OSPFv3 protocol Single-issue protocol is a separate one. It differs from the other in terms of road-based rather than network segment chain.

The next thing is to say the mistake ?

Options:

Two routers connected to the link, even if their IPv6 addresses are differently suffixed, they can still establish a neighbor relationship.

Pairing the two routers connected to the road, even if you do not configure the broadcast IPv6 address, you can establish a neighbor.

The OSPFv3 Link-local router obtains the next hop of the neighboring address from the neighboring routing information.

In addition to the virtual connection, all interfaces use the address of the address composition OSPFv3 Link-local

Question 44

The following is about RADIUS? Which is the correct way?

Options:

MAC, RADIUS authentication account code does not need to use the name secret, so you cannot use the identity authentication account.

RADIUS Portal, Portal, Portal authentication and authentication can not be used. Generally, the server can be used for identity authentication when deployed for authentication.

RADIUS protocol authentication, granting separation rights audit.

RADIUS supports with and without two access methods.

Question 45

Ip ip-prefix ip-prefix-name [ index index-number ] { permit | deny } ipv4-address mask-length [ matchnetwork ] [ greater-equal greater-equal-value ] [ less-equal less-equal-value ] Ip-prefix- is used for configuration. If a prefix

The list has been assigned 1ess -equal- , greater-equal4- , ? but not specified, then the previous fan is the number of

Options:

[mask-length ,less-equal-value]

[less-equal-value,32]

No restrictions

[0, less-equal-value]

Question 46

The following is about reliability, describing LDP errors?

Options:

The LDP FRR LSP LSP can also be generated from the mapping of the non-lowest hops as the privilege label, and the primary device is configured as the primary device. The table forwarding entry B. LDP IGP IGP LDP IGP is associated with the association. , guaranteed to be consistent with the path

Hand-configured dynamic LDP FRR 32 LDP LSP policy is the default route to the backup device.

LDP GR (Graceful Restart) MPLS uses the feature that the plane and the control plane are separated, and is forwarded when the device protocol is replaced by the restart or the primary or the reverse.

No interruption.

Question 47

If the router only needs to forward IPv6, IPv4 packets, then there is no need to configure any of these and address protocols on the router.

Options:

True

False

Question 48

One of the VXLAN BD VNIs can have multiple correspondences

Options:

Correct

Error

Question 49

In which port can provide a copy of the path to the generated root point RSTP sufficient tree section? What is the port?

Options:

Alternate Learning port and status

Alternate Forwarding Port and Status

Root port and shape Listening state

Designate Listening port and status

Alternate Discarding port and status

Question 50

HTTP TCP TCP Flood The HTTP Flood protocol is based on , so you can use the attack defense method to defend against attacks.

Options:

Error

Correct

Question 51

In the network, IPv6 A B A B NS B NA , two nodes and neighbors are neighbors. If the node sends a message to the node, if the node receives the message, it will reply.

The news, look at the point on the section A, what status will be the status of the neighborhood?

Options:

Reachable

Stale

Probe

Incomplete

Question 52

As shown in the picture, AS100 AS400, AS200, AS300 have two paths, and the best route from the recognition is that the most route is now known.

The path of AS400, R2, , is more bandwidth-efficient. Therefore, the following configuration is performed. After the configuration is completed, the most routes are not changed.

Configuration is in effect?

[R2]ip as-path-filter 1 permit^400$

R2]route-policy med permit node 10

R2-route-policy]if-match as-path-filter 1

Ir2-route-policy]apply cost 20

Options:

Configure R1 BGP deterministic-med in the process

Configure R2 BGP compare- different-as-med in the process

Configure R2 BGP deterministic-med in the process

Configure R1 BGP compare- different-as-med in the process

Question 53

Look at all the network devices on a network to check the information of the VPN ( ) detailed example. If the following is the case, which of the following methods is wrong? Multiple selection

Options:

The number of instances of the enabled address cluster in the local configuration is VPN Ipv6 1 real.

The book is assigned a label for each route of the VPN-instance vpna.

VPN-Instance vpna RT 2:1 VPN will not receive the route

GigabitEthernet1/0/0 interface has been added to the VPN-Instance vpna

Question 54

The following is true about the arm echo function method. There is a BFD ( ) single statement.

Options:

BFD single must be identified. Remote identification. The arm echo function must be configured with local symbols and terminators.

BFD IP 224.0.0.184 Single Protocol Report The purpose of the arm echo function is

BFD BFD Single Device The arm echo function is available for one support and the other does not support the scene.

BFD BFD IP IP After the one-arm echo function is enabled, the destination report of the text is the same as the source.

Question 55

In addition to the non-morphological address self-configuration, you can pass the IPv6 DHCPv6 DNS device to obtain the address, gateway, and other information.

Options:

Correct

Error

Question 56

The following topology diagram can be established through the R1 R2 R3 internet R1 R2 R1 R3 EBGP R2, R3 and access, and , and

By AS BGP R1 internet R2 ( ), the default route is advertised, and the traffic required for access is preferred. The following practices can be implemented.

Options:

R2 R1 export MED 150 specifies that the body pair is set in the direction attribute

R1 R3 import MED 150 specifies the body to be set in the direction attribute

R2 R1 export 150 specifies the body to set the priority in the direction

R1 R2 import 150 specifies that the body is set to the local direction in the direction.

Question 57

If you need to use the command in the local routing table without the default route, the command will be sent to the group IP, default route-import, BGP ( )

Provincial route,

Options:

True

False

Question 58

The following is about routing BGP, ?( ) selection description is wrong

Options:

Non-aggregated routing precedes aggregation routing.

In the case of equal and equal If the locally generated route, route, route Pref-Val local_preference, IBGP EBGP BGP preference

Consistent locally generated valid routes first, then excellent

See the following entry in the routing table BGP :* 172.16.1.11/32 0.0.0.0 10 0 ? Represents the route available.

For nexthop, the unreachable route is invalid and does not participate in the preference.

Question 59

IPSG DHCP-snooping can be configured to statically bind or bind to a table.

Options:

True

False

Correct

Question 60

Regarding the logical mode of the MPLS TTL pair, is the following description correct?

Options:

Pipe IP MPLS IP TTL 1 In MPLS TTL mode, when the message passes through the network, it is mapped to the field at the ingress point.

MPLS TTL IP TTL MPLS A label, which has the same function as the header, can prevent the network from routing the loop (as it is)

Uniform IP MPLS IP TTL 1 MPLS TTL mode is simulated. When the message passes through the network, the entry point is reduced and the field is fixed to the value.

In the case of the MPLS VPN MPLS Ingress uniform, the private network text can be used in the reporting mode.

Question 61

The following rules regarding the attributes of the ISIS LSP protocol report are correct.

Options:

LSP, LSP, LSDB fast dispersion characteristics expansion will be less than the specified number of out-of-band expansion

When the LSP is generated and the generated smart controller is generated, the time-varying frequency delay delay timer can be self-deferred according to the routing information rate.

When the road information increases the chain state, SP and LSP can increase the length of the grammar so that each can carry more information.

Reduce the minimum interval for sending LSP LSPs on the interface to speed up the diffusion between time.

Question 62

As shown in the figure, when running R1.R2.R3 OSPF and declaring their respective loops, what is wrong as described below?

Options:

R2 filter-policy export R3 can use the loopback route of the command filtering.

R2 Area1 filter export R3 can use the loopback route of the command filtering

R2 Area0 filter import R3 can be used in the commanded loop routing ring

R1 filter-policy import R3 can use filtered loop routing ring

Question 63

The port shaping rate is set to 100 Mbps PIR, and the bandwidth of the service input and configuration of the interface is as follows. Then the first round of rotation, the assigned team

What is the bandwidth?

Options:

30M

15M

90M

25M

Question 64

The result of the graph is combined with the results. The following is correct.

Options:

R3 level-1 DIS must be a certain chain

R3 level-2 router is a router

R3 level-2 DIS must be a certain chain

R3 system ID 0003.0000.0000 for the router

Question 65

The following description of the aggregation is correct for BGP, ?( ) radio

Options:

After the configuration, only Aggregate ipv4-address mask is sent, and the route is not specified.

For IPv6, BGP routing supports manual aggregation and self-aggregation.

By default, self-aggregation BGP is enabled.

You can manually aggregate the routes in the BGP local routing table.

Question 66

Regarding the cross-domain scenario, the following describes the VPN Option-B error?

Options:

Reporting In the forwarded mode, the ASBR VPN LSP exchanges on the two private networks to be paired.

Two neighbor relationships between ASBR MP-EBGP need to be established.

The cross-domain scheme is not limited by the number of interconnections. VPN-option-B ASBR is linked.

Two ASBR VPNv4 inter-exchange routes are exchanged with external label.

Question 67

In the process of using LACP, ? (the agreement is as follows, the correct one is multiple choice

Options:

You can avoid the Eth-Trunk interface due to physical path caused by the following commands.

You can use the following command to configure the row source chain in the enabled route aggregation. IP: interface eth-trunk 1 address line share into the load

Load-balance src-dst-ip

: You can use the following command to divide the interface into the chain aggregation in the enabled route aggregation.

Interface Gigabitethemnet0/0/0

Debug

Interface Gigabitethernet0/0/1

Undo eth-trunk 1

Interface Gigabitetheret0/0/

Undo shutdown

You can join the interface group member through the channel aggregation enabled by the following command:

Interface Gigabitethernet0/0/1 shutdown

Interface Gigabitethernet0/0/1 trunkport Gigabitethernet0/0/ interface Gigabitethernet0/0/1 undo shutdown

Question 68

About the routing entry method is correct R2 said?

Options:

2020::/64 IP router will appear in the current routing table.

2022::/64 IP router will appear in the current routing table.

2019::/64 IP router will appear in the current routing table.

2021::/64 IP router will appear in the current routing table.

Question 69

When the deployment needs to configure the parameter LLQ, ? Bandwidth Bandwidth Meaning What is the meaning of the parameter

Options:

Provide a built-in policer to limit the maximum available time of the queue.

The parameters should be as small as possible. It means that the bandwidth is always reserved, LLQ, even if the bandwidth parameter is used, the interface is available.

It indicates the reference to calculate the sudden size of the built-in tactical counter bucket.

The option parameter is a OK, LLQ because it starts with the other columns.

Question 70

In order to check the router R1 ""R1 "display ip routing-table" R1 OSPF routing table, execute the command on the route. Router running protocol. Below

What is the correct description of the information in the routing table is OSPF?

Options:

In the routing table, the routing table with the indicator indicates that the table is "O_ASE". 1 LSA 2 LSA is marked with the identifier that the item is classified or learned.

In the routing table, the routing table with the indicator can only be used to refer to the “O_ASE” tag that is learned by the route.

In the routing table, the route marked with the indicator indicates that the internal route of the area is “O_IA”.

In the routing table, the routing table with the indicator is introduced from other programs to the "OSPF" OSPF 7 LSA standard.

In the routing table, all types of LSAs have unique destination addresses.

Question 71

Established as shown below, R1.R2 E-BGP, BFD, neighbor and open function detection The following method is correct

Options:

R2 BFD 800ms text report detection time is

R2 BFD 600ms text report detection time is

R1 BD 660ms text report detection time is

R1 BFD 1280ms text report detection time is

Question 72

The following is about IPv6 Over VXLAN?

Options:

IPv6 over VXLAN Vxlan Overlay IPv6 refers to the network is the network

IPv6 over VXLAN IP can solve the problem of insufficient capital for the terminal address source.

VXLAN IPv4 The tunnel of the gateway is an inter-layer network.

IPv6 Over VXLAN does not generate entries.

Question 73

About the prevention mechanism BGP, ? ring The following description is correct

Options:

The AS-PATH attribute of the autonomous system is used to prevent the loop.

Cluster List Cluster List The Cluster ID attribute is used for the anti-ring in the reflector cluster. The discovery of the router routing entry contains its own and will reject the

routing.

The learned route will not announce to IBGP IBGP, AS neighbor is used to prevent internal routing loops.

You can use the attribute to prevent the AS-CONFED-SET link in the alliance.

Question 74

In the experimental network, the network is built according to the following topology. The SW1 SW2 STP is configured as the default and the function is disabled. The scene description is correct.

Options:

Sw1 G0/0/2 Discarding entry status

sw2 G0/0/1 Discarding entry status

sw2 G0/0/2 Discarding entry status

No interface is blocked

SW1 G0/0/1 Discarding entry status

Load More H12-261 Questions

Black Friday Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: 70percent

Huawei H12-261 HCIE-Routing & Switching (Written) Exam Practice Test

HCIE-Routing & Switching (Written) Questions and Answers

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options:

Answer:

Options: