New Year Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: 70percent

Certensure Logo
  1. Home
  2. Fortinet
  3. Fortinet Certification
  4. NSE7_SDW-7.0 - Fortinet NSE 7 - SD-WAN 7.0

Fortinet NSE7_SDW-7.0 Fortinet NSE 7 - SD-WAN 7.0 Exam Practice Test

Demo: 21 questions
Total 70 questions
Get NSE7_SDW-7.0 Full Access Download NSE7_SDW-7.0 PDF

Fortinet NSE 7 - SD-WAN 7.0 Questions and Answers

Question 1

What are two benefits of using forward error correction (FEC) in IPsec VPNs? (Choose two.)

Options:

A.

FEC supports hardware offloading.

B.

FEC improves reliability of noisy links.

C.

FEC transmits parity packets that can be used to reconstruct packet loss.

D.

FEC can leverage multiple IPsec tunnels for parity packets transmission.

Question 2

Which two protocols in the IPsec suite are most used for authentication and encryption? (Choose two.)

Options:

A.

Encapsulating Security Payload (ESP)

B.

Secure Shell (SSH)

C.

Internet Key Exchange (IKE)

D.

Security Association (SA)

Question 3

Which two interfaces are considered overlay links? (Choose two.)

Options:

A.

LAG

B.

IPsec

C.

Physical

D.

GRE

Question 4

Refer to the exhibit.

The exhibit shows the SD-WAN rule status and configuration.

Based on the exhibit, which change in the measured packet loss will make T_INET_1_0 the new preferred member?

Options:

A.

When all three members have the same packet loss.

B.

When T_INET_0_0 has 4% packet loss.

C.

When T_INET_0_0 has 12% packet loss.

D.

When T_INET_1_0 has 4% packet loss.

Question 5

Refer to the exhibit.

FortiGate has multiple dial-up VPN interfaces incoming on port1 that match only FIRST_VPN.

Which two configuration changes must be made to both IPsec VPN interfaces to allow incoming connections to match all possible IPsec dial-up interfaces? (Choose two.)

Options:

A.

Specify a unique peer ID for each dial-up VPN interface.

B.

Use different proposals are used between the interfaces.

C.

Configure the IKE mode to be aggressive mode.

D.

Use unique Diffie Hellman groups on each VPN interface.

Question 6

In a hub-and-spoke topology, what are two advantages of enabling ADVPN on the IPsec overlays? (Choose two.)

Options:

A.

It provides the benefits of a full-mesh topology in a hub-and-spoke network.

B.

It provides direct connectivity between spokes by creating shortcuts.

C.

It enables spokes to bypass the hub during shortcut negotiation.

D.

It enables spokes to establish shortcuts to third-party gateways.

Question 7

Which three matching traffic criteria are available in SD-WAN rules? (Choose three.)

Options:

A.

Type of physical link connection

B.

Internet service database (ISDB) address object

C.

Source and destination IP address

D.

URL categories

E.

Application signatures

Question 8

Two hub-and-spoke groups are connected through a site-to-site IPsec VPN between Hub 1 and Hub 2. The administrator configured ADVPN on both hub-and-spoke groups.

Which two outcomes are expected if a user in Toronto sends traffic to London? (Choose two.)

Options:

A.

London generates an IKE information message that contains the Toronto public IP address.

B.

Traffic from Toronto to London triggers the dynamic negotiation of a direct site-to-site VPN.

C.

Toronto needs to establish a site-to-site tunnel with Hub 2 to bypass Hub 1.

D.

The first packets from Toronto to London are routed through Hub 1 then to Hub 2.

Question 9

Which components make up the secure SD-WAN solution?

Options:

A.

Application, antivirus, and URL, and SSL inspection

B.

Datacenter, branch offices, and public cloud

C.

FortiGate, FortiManager, FortiAnalyzer, and FortiDeploy

D.

Telephone, ISDN, and telecom network.

Question 10

Refer to the exhibit.

Based on the exhibit, which statement about FortiGate re-evaluating traffic is true?

Options:

A.

The type of traffic defined and allowed on firewall policy ID 1 is UDP.

B.

FortiGate has terminated the session after a change on policy ID 1.

C.

Changes have been made on firewall policy ID 1 on FortiGate.

D.

Firewall policy ID 1 has source NAT disabled.

Question 11

Refer to the exhibits.

Exhibit A -

Exhibit B -

Exhibit A shows the SD-WAN performance SLA and exhibit B shows the SD-WAN member status, the routing table, and the performance SLA status.

If port2 is detected dead by FortiGate, what is the expected behavior?

Options:

A.

Port2 becomes alive after three successful probes are detected.

B.

FortiGate removes all static routes for port2.

C.

The administrator manually restores the static routes for port2, if port2 becomes alive.

D.

Host 8.8.8.8 is reachable through port1 and port2.

Question 12

Which two statements are true about using SD-WAN to steer local-out traffic? (Choose two.)

Options:

A.

FortiGate does not consider the source address of the packet when matching an SD-WAN rule for local-out traffic.

B.

By default, local-out traffic does not use SD-WAN.

C.

By default, FortiGate does not check if the selected member has a valid route to the destination.

D.

You must configure each local-out feature individually, to use SD-WAN.

Question 13

What is the route-tag setting in an SD-WAN rule used for?

Options:

A.

To indicate the routes for health check probes.

B.

To indicate the destination of a rule based on learned BGP prefixes.

C.

To indicate the routes that can be used for routing SD-WAN traffic.

D.

To indicate the members that can be used to route SD-WAN traffic.

Question 14

Refer to the exhibit.

Which configuration change is required if the responder FortiGate uses a dynamic routing protocol to exchange routes over IPsec?

Options:

A.

type must be set to static.

B.

mode-cfg must be enabled.

C.

exchange-interface-ip must be enabled.

D.

add-route must be disabled.

Question 15

Refer to the exhibit.

Which statement explains the output shown in the exhibit?

Options:

A.

FortiGate performed standard FIB routing on the session.

B.

FortiGate will not re-evaluate the session following a firewall policy change.

C.

FortiGate used 192.2.0.1 as the gateway for the original direction of the traffic.

D.

FortiGate must re-evaluate the session due to routing change.

Question 16

Refer to the exhibits.

Which two statements about the IPsec VPN configuration and the status of the IPsec VPN tunnel are true? (Choose two.)

Options:

A.

FortiGate does not install IPsec static routes for remote protected networks in the routing table.

B.

The phase 1 configuration supports the network-overlay setting.

C.

FortiGate facilitated the negotiation of the T_INET_1_0_0 ADVPN shortcut over T_INET_1_0.

D.

Dead peer detection is disabled.

Question 17

Which statement is correct about SD-WAN and ADVPN?

Options:

A.

Routes for ADVPN shortcuts must be manually configured.

B.

SD-WAN can steer traffic to ADVPN shortcuts, established over IPsec overlays, configured as SD-WAN members.

C.

SD-WAN does not monitor the health and performance of ADVPN shortcuts.

D.

You must use IKEv2 on IPsec tunnels.

Question 18

Refer to the exhibit.

Based on the output, which two conclusions are true? (Choose two.)

Options:

A.

There is more than one SD-WAN rule configured.

B.

The SD-WAN rules take precedence over regular policy routes.

C.

The all_rules rule represents the implicit SD-WAN rule.

D.

Entry 1(id=1) is a regular policy route.

Question 19

Which two conclusions for traffic that matches the traffic shaper are true? (Choose two.)

Options:

A.

The traffic shaper drops packets if the bandwidth is less than 2500 KBps.

B.

The measured bandwidth is less than 100 KBps.

C.

The traffic shaper drops packets if the bandwidth exceeds 6250 KBps.

D.

The traffic shaper limits the bandwidth of each source IP to a maximum of 6250 KBps.

Question 20

Refer to the exhibit, which shows the IPsec phase 1 configuration of a spoke.

What must you configure on the IPsec phase 1 configuration for ADVPN to work with SD-WAN?

Options:

A.

You must set ike-version to 1.

B.

You must enable net-device.

C.

You must enable auto-discovery-sender.

D.

You must disable idle-timeout.

Question 21

What are two reasons why FortiGate would be unable to complete the zero-touch provisioning process? (Choose two.)

Options:

A.

The FortiGate cloud key has not been added to the FortiGate cloud portal.

B.

FortiDeploy has connected with FortiGate and provided the initial configuration to contact FortiManager

C.

The zero-touch provisioning process has completed internally, behind FortiGate.

D.

FortiGate has obtained a configuration from the platform template in FortiGate cloud.

E.

A factory reset performed on FortiGate.

Load More NSE7_SDW-7.0 Questions
Demo: 21 questions
Total 70 questions
Get NSE7_SDW-7.0 Full Access Download NSE7_SDW-7.0 PDF