Fortinet FCSS_SASE_AD-23 FCSS FortiSASE 23 Administrator Exam Practice Test

The VPN tunnel between the FortiSASE spoke and the FortiGate hub is not establishing due to the configuration of mode config, which is not supported by FortiSASE spoke devices. Mode config is used to assign IP addresses to VPN clients dynamically, but this feature is not applicable to FortiSASE spokes.

Mode Config in IPsec:

The configuration snippet shows that mode config is enabled in the IPsec phase 1 settings.

Mode config is typically used for VPN clients to dynamically receive an IP address from the VPN server, but it is not suitable for site-to-site VPN configurations involving FortiSASE spokes.

Configuration Adjustment:

To establish the VPN tunnel, you need to disable mode config in the IPsec phase 1 settings.

This adjustment will allow the FortiSASE spoke to properly establish the VPN tunnel with the FortiGate hub.

Steps to Disable Mode Config:

Access the VPN configuration on the FortiSASE spoke.

Edit the IPsec phase 1 settings to disable mode config.

Ensure other settings such as pre-shared key, remote gateway, and BGP configurations are correct and consistent with the FortiGate hub.

References:

FortiOS 7.2 Administration Guide: Provides details on configuring IPsec VPNs and mode config settings.

FortiSASE 23.2 Documentation: Explains the supported configurations for FortiSASE spoke devices and VPN setups.

When accessing the FortiSASE portal for the first time, an administrator must select data center locations for the following FortiSASE components:

Endpoint Management:

The data center location for endpoint management ensures that endpoint data and policies are managed and stored within the chosen geographical region.

Points of Presence (PoPs):

Points of Presence (PoPs) are the locations where FortiSASE services are delivered to users. Selecting PoP locations ensures optimal performance and connectivity for users based on their geographical distribution.

Logging:

The data center location for logging determines where log data is stored and managed. This is crucial for compliance and regulatory requirements, as well as for efficient log analysis and reporting.

References:

FortiOS 7.2 Administration Guide: Details on initial setup and configuration steps for FortiSASE.

FortiSASE 23.2 Documentation: Explains the importance of selecting data center locations for various FortiSASE components.

To configure a Secure Private Access (SPA) solution to share endpoint information between FortiSASE and a corporate FortiGate, you need to take the following steps:

Add the FortiGate IP address in the secure private access configuration on FortiSASE:

This step allows FortiSASE to recognize and establish a connection with the corporate FortiGate.

Use the FortiClient EMS cloud connector on the corporate FortiGate to connect to FortiSASE:

The EMS (Endpoint Management Server) cloud connector facilitates the integration between FortiClient endpoints and FortiSASE, enabling seamless sharing of endpoint information.

Register FortiGate and FortiSASE under the same FortiCloud account:

By registering both FortiGate and FortiSASE under the same FortiCloud account, you ensure centralized management and synchronization of configurations and policies.

References:

FortiOS 7.2 Administration Guide: Provides details on configuring Secure Private Access and integrating with FortiGate.

FortiSASE 23.2 Documentation: Explains how to set up and manage connections between FortiSASE and corporate FortiGate.

Zero Trust Network Access (ZTNA) is the FortiSASE feature that ensures least-privileged user access to all applications. ZTNA operates on the principle of "never trust, always verify," providing secure access based on the identity of users and devices, regardless of their location.

Zero Trust Network Access (ZTNA):

ZTNA ensures that only authenticated and authorized users and devices can access applications.

It applies the principle of least privilege by granting access only to the resources required by the user, minimizing the potential for unauthorized access.

Implementation:

ZTNA continuously verifies user and device trustworthiness and enforces granular access control policies.

This approach enhances security by reducing the attack surface and limiting lateral movement within the network.

References:

FortiOS 7.2 Administration Guide: Provides detailed information on ZTNA and its role in ensuring least-privileged access.

FortiSASE 23.2 Documentation: Explains the implementation and benefits of ZTNA within the FortiSASE environment.

Based on the provided exhibits, the reason why the Win7-Pro endpoint can no longer access the internet through FortiSASE is due to exceeding the total vulnerability detected threshold. This threshold is used to determine if a device is compliant with the security requirements to access the network.

Endpoint Compliance:

FortiSASE monitors endpoint compliance by assessing various security parameters, including the number of vulnerabilities detected on the device.

The compliance status is indicated by the ZTNA tags and the vulnerabilities detected.

Vulnerability Threshold:

The exhibit shows that Win7-Pro has 176 vulnerabilities detected, whereas Win10-Pro has 140 vulnerabilities.

If the endpoint exceeds a predefined vulnerability threshold, it may be restricted from accessing the network to ensure overall network security.

Impact on Network Access:

Since Win7-Pro has exceeded the vulnerability threshold, it is marked as non-compliant and subsequently loses internet access through FortiSASE.

The FortiSASE endpoint profile enforces this compliance check to prevent potentially vulnerable devices from accessing the internet.

References:

FortiOS 7.2 Administration Guide: Provides information on endpoint compliance and vulnerability management.

FortiSASE 23.2 Documentation: Explains how vulnerability thresholds are used to determine endpoint compliance and access control.

The Secure Internet Access (SIA) use case that minimizes individual workstation or device setup is SIA for agentless remote users. This use case does not require installing FortiClient on endpoints or configuring explicit web proxy settings on web browser-based endpoints, making it the simplest and most efficient deployment.

SIA for Agentless Remote Users:

Agentless deployment allows remote users to connect to the SIA service without needing to install any client software or configure browser settings.

This approach reduces the setup and maintenance overhead for both users and administrators.

Minimized Setup:

Without the need for FortiClient installation or explicit proxy configuration, the deployment is straightforward and quick.

Users can securely access the internet with minimal disruption and administrative effort.

References:

FortiOS 7.2 Administration Guide: Details on different SIA deployment use cases and configurations.

FortiSASE 23.2 Documentation: Explains how SIA for agentless remote users is implemented and the benefits it provides.

In the user connection monitor, the random characters shown for the username indicate that log anonymization is enabled. Log anonymization is a feature that hides the actual user information in the logs for privacy and security reasons. To display proper user information, you need to disable log anonymization.

Log Anonymization:

When log anonymization is turned on, the actual usernames are replaced with random characters to protect user privacy.

This feature can be beneficial in certain environments but can cause issues when detailed user monitoring is required.

Disabling Log Anonymization:

Navigate to the FortiSASE settings.

Locate the log settings section.

Disable the log anonymization feature to ensure that actual usernames are displayed in the logs and user connection monitors.

References:

FortiSASE 23.2 Documentation: Provides detailed steps on enabling and disabling log anonymization.

Fortinet Knowledge Base: Explains the impact of log anonymization on user monitoring and logging.

If the daily summary report generated by FortiSASE contains very little data, one possible explanation is that the "Log allowed traffic" setting is configured to log only "Security Events" for all policies. This configuration limits the amount of data logged, as it only includes security events and excludes normal allowed traffic.

Log Allowed Traffic Setting:

The "Log allowed traffic" setting determines which types of traffic are logged.

When set to "Security Events," only traffic that triggers a security event (such as a threat detection or policy violation) is logged.

Impact on Report Data:

If the log setting excludes regular allowed traffic, the amount of data captured and reported is significantly reduced.

This results in reports with minimal data, as only security-related events are included.

References:

FortiOS 7.2 Administration Guide: Provides details on configuring logging settings for traffic policies.

FortiSASE 23.2 Documentation: Explains the impact of logging configurations on report generation and data visibility.

To resolve internal hostnames using internal DNS servers for remotely connected endpoints, the following two components must be configured on FortiSASE:

Split DNS Rules:

Split DNS allows the configuration of specific DNS queries to be directed to internal DNS servers instead of public DNS servers.

This ensures that internal hostnames are resolved using the organization's internal DNS infrastructure, maintaining privacy and accuracy for internal network resources.

Split Tunneling Destinations:

Split tunneling allows specific traffic (such as DNS queries for internal domains) to be routed through the VPN tunnel while other traffic is sent directly to the internet.

By configuring split tunneling destinations, you can ensure that DNS queries for internal hostnames are directed through the VPN to the internal DNS servers.

References:

FortiOS 7.2 Administration Guide: Provides details on configuring split DNS and split tunneling for VPN clients.

FortiSASE 23.2 Documentation: Explains the implementation and configuration of split DNS and split tunneling for securely resolving internal hostnames.