Which statement is true regarding Brocade NOS Virtual Fabrics?
You are an administrator at a cloud-based provider. You need a solution that provides L3 multi-tenancy to enable separate resources to be used by your customers.
Which feature would resolve this problem?
When connecting the Brocade VDX Fabric to an Ethernet switch with spanning tree disabled, CPU utilization goes up indicating a loop.
What is causing the loop?
You need to deploy several FCoE initiators to communicate to existing FC SAN attached targets.
Which two statements are true about deploying the solution? (Choose two.)
Which three parameters would be configured in an AMPP port profile? (Choose three.)
Which feature simplifies deployment of QoS for IP-based storage in a Brocade VCS Fabric?
Exhibit:
VDX11# show vcs detail
Config Mode : Distributed
VCS ID : 10
Total Number of Nodes : 3
Node :1
Serial Number : BWW2535G00E
Condition : Good
Status : Co-ordinator
VCS Id : 10
Rbridge-Id : 10
Co-ordinator : YES
WWN : 10:00:00:05:33:91:3D:F4
Switch MAC : 00:05:33:91:3D:F4
FCF MAC : 0C:B3:1E:F8:0C:B3
Internal IP : 127.1.0.10
Management IP : 10.255.248.24
Exhibit:
Referring to the exhibit, in which mode of operation is the active switch participating?
You want to capture sFlow statistics from a group of interfaces on a Brocade VDX and forward the data to your Brocade Network Advisor server.
Which three steps are required for a working configuration? (Choose three.)
A customer would like to use Brocade VDX switches for connectivity to servers running at 100 Mbps and 1000 Mbps. The customer would also like the option to upgrade the switch ports to 10 Gbps for additional bandwidth in the near future.
Which Brocade VDX switch should you use?
Your customer would like to control a Brocade VCS Fabric consisting of four Brocade VDX 6740s by using SSH to the same address on the principal switch in the fabric.
Which two attributes should be configured to accomplish this? (Choose two.)
A customer has a four-port vLAG between two VDX switches and a server. Two of the four links are up but the vLAG will not come up.
VDX8770_3-131# show interface po 710
Port-channel 710 is up, line protocol is down (link protocol down)
Hardware is AGGREGATE, address is 0005.33d4.0d2c
Current address is 0005.33d4.0d2c
Interface index (ifindex) is 671089350
Minimum number of links to bring Port-channel up is 3
MTU 2500 bytes
LineSpeed Actual : Nil
Allowed Member Speed : 10000 Mbit
Priority Tag disable
IPv6 RA Guard disable
Last clearing of show interface counters: 2d05h53m
Queueing strategy: fifo
Receive Statistics:
0 packets, 0 bytes
Unicasts: 0, Multicasts: 0, Broadcasts: 0
64-byte pkts: 0, Over 64-byte pkts: 0, Over 127-byte pkts: 0
Over 255-byte pkts: 0, Over 511-byte pkts: 0, Over 1023-byte pkts: 0
Over 1518-byte pkts(Jumbo): 0
Runts: 0, Jabbers: 0, CRC: 0, Overruns: 0
Errors: 0, Discards: 0
Transmit Statistics:
0 packets, 0 bytes
Unicasts: 0, Multicasts: 0, Broadcasts: 0
Underruns: 0
Errors: 0, Discards: 0
Rate info (interval 299 seconds):
Input 0.000000 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Output 0.000000 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Time since last interface status change: 2d05h53m
What should the customer do to bring the vLAG online?
Referring to the exhibit, you have configured VRRP-E in your Brocade VCS Fabric on two switches connected to your intranet. You want to prevent unnecessary traffic on the ISL links.
Which feature would you use to accomplish this task?
A customer would like to manage their Brocade VDX switch but is having problems connecting from the Brocade Network Advisor server at IP address 10.10.30.15.
ip access-list standard access1
seq 5 permit host 10.10.20.0/24
seq 100 deny any log
interface Management 125/0
ip access-group access1 in
Referring to the exhibit, what are two reasons for this happening? (Choose two.)
When creating a vLAG on a Brocade VDX, which statement is correct?
A customer wants to connect a group of servers to different Brocade VDXs in a three switch Brocade VDX 6740 fabric. All servers should have one gateway and should failover if one switch is taken offline for maintenance. The individual VDX should forward all packets to the destination from the VDX that receives them.
How should this solution be implemented?
Referring to the exhibit,
which configuration is valid?
You are troubleshooting an FCoE login problem in your environment. The port shown in the exhibit has not been able to log into the fabric. The default FCoE fabric map in your environment has not been changed.
Interface TenGigabitEthernet 3/0/4
Mode PFC
DCBX enabled for PFC negotiation
TX 0 frames
TX TX RX RX Output Paused
CoS Admin Oper Admin Oper 512 BitTimes
---------------------------------------
0 Off Off Off Off 0
1 Off Off Off Off 0
2 Off Off Off Off 0
3 On Off On Off 0
4 Off Off Off Off 0
5 Off Off Off Off 0
6 Off Off Off Off 0
7 Off Off Off Off 0
sw0(conf-if-te-3/0/1-24)# do show lldp neighbors interface ten 3/0/4 detail
Neighbors for Interface Te 3/0/4
---
DCBX TLVs
===========
Version : CEE
DCBX Ctrl OperVersion: 0 MaxVersion: 0 SeqNo: 4 AckNo: 6
DCBX ETS OperVersion: 0 MaxVersion: 0 Enabled: 1 Willing: 0 Error: 1
Enhanced Transmission Selection (ETS)
Priority-Group ID Map:
Priority : 0 1 2 3 4 5 6 7
Group ID : 0 0 0 0 1 0 0 0
Group ID Bandwidth Map:
Group ID : 0 1 2 3 4 5 6 7
Percentage: 50 50 0 0 0 0 0 0
Number of Traffic Classes supported: 2
DCBX PFC OperVersion: 0 MaxVersion: 0 Enabled: 0 Willing: 0 Error: 1
Priority-based Flow Control (PFC)
Enabled Priorities: 3
Number of Traffic Class PFC supported: 8
FCoE App OperVersion: 0 MaxVersion: 0 Enabled: 1 Willing: 0 Error: 0
FCoE Application Protocol
User Priorities: 4
What are two causes of the problem? (Choose two.)
You have formed a Brocade VCS fabric with four switches.
Referring to the exhibit, which Brocade VDX would be the principal RBridge?
You are attempting to merge two Brocade VDX switches running in fabric mode, but they segment.
sw0# show fabric islports
Name: sw0
Type: 96.5
State: Online
Role: Fabric Principal
VCS Id: 10
Config Mode:Distributed
Rbridge-id: 4
WWN: 10:00:00:05:33:91:48:f7
FCF MAC: 00:05:33:91:48:f7
sw0# show fabric islports
Name: sw0
Type: 96.5
State: Online
Role: Fabric Principal
VCS Id: 2
Config Mode:Distributed
Rbridge-id: 20
WWN: 10:00:00:05:33:90:92:e4
FCF MAC: 00:05:33:90:92:e4
Referring to the exhibit, what is the reason?
Your customer wants to establish a LAG connection on a Brocade VDX 6740T-1G connecting to another vendor's switch using 1 GbE interfaces. Every time they try to enable the port channel, the interfaces shut down.
In this situation, which statement is true?
Which three attributes are distributed by the Ethernet Name Server (eNS) within a Brocade VCS Fabric? (Choose three.)
In the exhibit, both MAC addresses are assigned to interface 2/0/4.
What does the (UC) indicate?
You are asked to deploy servers with a single adapter that is attached to your Brocade VCS Fabric to communicate with FC SAN attached storage.
Which two components are required? (Choose two.)
You are introducing a Brocade VCS Fabric to your network and want to implement a non-modular, top of rack switch with at least 40 GbE uplinks to the core.
Which switch would you use?
You just replaced a Brocade VDX in your four-switch VCS fabric.
Which two are enabled by default on the new VDX switch? (Choose two.)
You want to examine packets in transit across links to troubleshoot the traffic pattern on a specific port using SPAN on a Brocade VDX 6730-76. You configure a monitor session with source interface Te 1/0/10 and destination interface Te 1/0/21.
Which two statements are correct? (Choose two.)
You are attempting to merge two Brocade VDX switches, both running in fabric mode, but they segment.
sw0# show fabric islports
Name: sw0
Type: 96.5
State: Online
Role: Fabric Principal
VCS Id: 10
Config Mode:Local-only
Rbridge-id: 4
WWN: 10:00:00:05:33:91:48:f7
FCF MAC: 00:05:33:91:48:f7
sw0# show fabric islports
Name: sw0
Type: 96.5
State: Online
Role: Fabric Principal
VCS Id: 10
Config Mode:Distributed
Rbridge-id: 20
WWN: 10:00:00:05:33:90:92:e4
FCF MAC: 00:05:33:90:92:e4
Referring to the exhibit, what is the reason?