Winter Special Flat 65% Limited Time Discount offer - Ends in 0d 00h 00m 00s - Coupon code: suredis

Certensure Logo
  1. Home
  2. Brocade
  3. Interworking
  4. 150-130 - Brocade Certified Network Engineer 2012

Brocade 150-130 Brocade Certified Network Engineer 2012 Exam Practice Test

Demo: 16 questions
Total 113 questions
Get 150-130 Full Access Download 150-130 PDF

Brocade Certified Network Engineer 2012 Questions and Answers

Question 1

Your company uses OSPF and has recently purchased another company that uses RIP.

Management requires that routes between the two companies be shared without interrupting services on either network. How is this implemented?

Options:

A.

Enable route redistribution in both RIP and OSPF on the DR.

B.

Enable route redistribution in both RIP and OSPF on the BDR.

C.

Enable route redistribution in both RIP and OSPF on the ASBR.

D.

Enable route redistribution in both RIP and OSPF in the ABR.

Question 2

Which two results does the link-aggregate configure key command accomplish when creating Link Aggregation Groups (LAGs) on a FastIron device? (Choose two.)

Options:

A.

It encrypts the LAGs for security,

B.

It identifies LAG membership.

C.

It allows multiple LAGs to be configured on a device.

D.

It is used to configure VLANs on the LAG.

Question 3

Which two statements are true about QoS when implemented on a Brocade FastIron platform? (Choose two.)

Options:

A.

Packets with lower priority classifications are given a higher precedence for forwarding.

B.

Packets with higher priority classifications are given a higher precedence for forwarding.

C.

Stackable devices use CoS 0 for stacking communication.

D.

Stackable devices use CoS 7 for stacking communication.

Question 4

Which three statements are true about RIPv2 and OSPF? (Choose three.)

Options:

A.

RIPv2 is a distance vector and OSPF is a link state protocol.

B.

OSPF supports VLSM and RIPv2 does not.

C.

RIPv2 and OSPF support MD5 authentication.

D.

RIPv2 advertises its entire routing table and OSPF sends only updates.

E.

RIPv2 and OSPF use neighbor statements to configure peers.

Question 5

What are two Brocade stackable products? (Choose two.)

Options:

A.

Brocade Fastiron SX

B.

BrocadeFastIronCX

C.

BrocadelCX6430

D.

Brocade MLXe

Question 6

You need to troubleshoot problems with an optic connection on a Brocade MLXe device.

What information is displayed by show optic for each port on that slot? (Choose three.)

Options:

A.

This command displays the temperature information for the optic.

B.

This command displays the transmit power information for the optic.

C.

This command displays the number of interface flaps for the optic.

D.

This command displays the receive power information for the optic.

E.

This command displays the length of the fiber cable.

Question 7

Which two statements about ingress extended ACLs are correct? (Choose two.)

Options:

A.

They use extended ACL IDs 200 - 299.

B.

They save network resources by reducing traffic.

C.

They eliminate denial of service (DoS) attacks.

D.

They block unwanted traffic or users.

Question 8

Which two multicast routing protocols are supported on Brocade FastIron devices? (Choose two.)

Options:

A.

DVMRP

B.

PIM

C.

MBGP

D.

MOSPF

Question 9

In which stage is an OSPF neighbor adjacency complete?

Options:

A.

loading

B.

exchange

C.

two-way

D.

full

Question 10

An identical route has been discovered by OSPF and RIP. By default, the OSPF route is chosen and added to the routing table. What should be done to allow the RIP route to be preferred?

Options:

A.

Redistribute OSPF routes into RIP.

B.

Change the administrative distance.

C.

Raise the route's priority in RIP.

D.

Use the no router OSPF command.

Question 11

Which two features are implemented using Brocade IronStack technology? (Choose two.)

Options:

A.

You can use any port on the switches to create your IronStack.

B.

You can mix devices running different software images in the same stack group.

C.

You can manage multiple physical switches in an IronStack as a single logical switch.

D.

You can perform a hitless stack failover without impacting Layer 2 and Layer 3 unicast traffic.

Question 12

Users connected to Switch1 are unable to access a database server connected to Switch2.

Referring to the exhibit, what are three explanations? (Choose three.)

Options:

A.

Port 1/1/1 on Switch2 is administratively disabled.

B.

Port 1/1/1 on Switch1 is administratively disabled.

C.

One of the switches has a defective port.

D.

The cable between the two switches is damaged.

E.

Port 1/1/1 on Switch1 has Spanning Tree disabled.

Question 13

What is the purpose of the Brocade MLXe SNMP trap hold-down timer?

Options:

A.

to send all traps before a router reboot

B.

to wait for convergence to occur before sending traps

C.

to wait for UDP connection establishment before sending traps

D.

to wait for TCP connection establishment before sending traps

Question 14

What are two uses for port-based VLANs? (Choose two.)

Options:

A.

Create separate broadcast domains inside a single Layer 2 network.

B.

Segregate traffic at Layer 3.

C.

Eliminate the need for routers between different subnets.

D.

Separate user traffic into different logical network segments based on department.

Question 15

What is the CIDR notation for the IP address range: 192.115.0.0 -192.115.3.255?

Options:

A.

192.115.0.0/22

B.

192.115.0.0/24

C.

192.115.0.1/22

D.

192.115.0.1/24

Question 16

Which three transceiver form factors are supported by Brocade switches and routers? (Choose three.)

Options:

A.

XPAK

B.

SFP

C.

SFP+

D.

X2

E.

XFP

Load More 150-130 Questions
Demo: 16 questions
Total 113 questions
Get 150-130 Full Access Download 150-130 PDF